Please read the instructions carefully!

Explanations of pole names and their locations are provided below.

GENERAL REQUIREMENTS:
The map must include a medium voltage (MV) main line, starting at one end of the map, from which additional MV lines lead to the transformer station. The main line may end at the transformer station in the village or extend beyond the map. Transformer stations are placed in villages (preferably one transformer per village) or in areas such as biogas plants/sawmills/elevators, etc. In this case, we remove everything from the “osprzęt_nN” group except for the “kabelZiemny” group. If we place such a station in a village, we only remove the equipment that we do not need (e.g., if we only run lines with lighting on insulated wires on the right and left from the transformer station, we remove the equipment for lines on insulated wires, the “distribution” group from the ‘insulatedWires’ group, and the “T” group (rear) from the “distribution+osw” group (for lines with lamps on a single insulated wire “distribution+osw” we use the “distribution” group, this is an exception), etc. From the LV poles, we run connections to buildings. They can also be made by placing an underground cable from the “equipment” - “underground cables” group on the pole (we select the appropriate cable for the appropriate pole, i.e., if we take a pole from the ‘zerdzieE’ (round) group, we select a cable from the “zerdzieE” group. Uninsulated wires can only be attached to appropriate insulators at the same height on the insulator as shown on the poles, insulated wires can only be attached to special holders as shown (when setting, turn the holder and scale the wire in the middle). Do not attach more than 1 wire to a connection on a single insulator/clamp or more than 1 line wire on either side of the insulator/clamp. Do not connect lines from two different transformer stations. A line on uninsulated cables with lamps must have 5 cables, without lamps 4, while a line on insulated cables with lamps must have either a “distribution” cable and an ‘osw’ cable, or one “distribution+osw” cable; without lamps, a “distribution” cable is sufficient. Connection accessories can be found in the “accessories” - “for connections” group (just read the group and model names). For a house alone, we can make a 1-phase connection (2 non-insulated wires on insulators or 1 insulated wire on the appropriate hook), and for a house with outbuildings, a 3-phase connection must be made (4 non-insulated wires on insulators or 1 insulated wire on the appropriate hook) . Where the line runs straight and does not turn, we use a P pole, and where the line turns, we use an N pole with a rotation such that: if the line in front of it has a direction of 0 and the line after the turn has a direction of 30, then the pole should have a direction of 15 (direction before + direction after / 2). where we draw an additional line from the line, we place an RPK pole if we draw it from a P pole, and if from an N pole, RNK (for the SN line, we must place RONK), at the end of the line we place a slupK pole, Kp and Ko poles are only used to terminate additional (side) lines.


POLE NAMES:
slupP - straight-through pole
	Place it in a straight line where the line does not change direction and the wires on either side do not hang over a paved 	road or buildings.

slupPS - straight-through-crossing pole
	Place it in a straight line where the line does not change direction and the wires on at least one side hang over a paved 	road or buildings.

slupRPK - branch-through-terminal pole
	Place it in a straight line where the line does not change direction and the wires on either side do not hang over a paved 	road or buildings, at the point from which you want to run a branch line (for MV - to the transformer, for LV - to the 	building(s)). If a pole has the suffix "s" (RPKs), an O (resistive)/ON (resistive-corner)/Or (resistive with 	disconnector)/ONr (resistive-corner with disconnector) pole must be placed on the side of the lateral line no more than 8 	meters from the pole. If the pole has the suffix "p," it means it is a pole with a support, which must be on the side of 	the lateral line conductors. If it has the suffix "o," it means it is a pole with a guy wire, which must be on the opposite 	side from the lateral line conductors.

slupRPSK - branch-through-crossing-terminal pole
	It is placed in a straight line, where the line does not change direction, and the conductors on at least one side hang 	over the asphalt road or buildings, at the point from which the lateral line is to be routed (for MV - to the transformer). 	If the pole has the suffix "s" (RPSKs), an O (resistance pole)/ON (resistance-corner pole)/Or (resistance pole with 	disconnector)/ONr (resistance-corner pole with disconnector) must be placed on the side of the secondary line no more than 	8 meters from the pole.

slupN - corner pole
	We place it where the line changes direction. If it is a medium-voltage pole and the conductors on one side hang over a 	paved road or buildings, we recommend using an N2 pole with additional insulators and support conductors. To achieve the 	proper rotation, you need to determine how many degrees the line should change direction in a given direction. After you 	have at least one column after the curved column, you need to rotate the corner column by half the specified value in the 	opposite direction (e.g., the line previously had a direction of 0 degrees, now it has a direction of 30 degrees, so the 	change is 30 degrees, and the curved column will have a rotation of 15 degrees, the formula for rotation is direction in 	front + direction behind / 2). If the column has a "p" suffix, it means it is a column with a support, which must be on the 	side of the curved line. If it has an "o" suffix, it means it is a column with a guy wire, which must be on the opposite 	side of the curve.

slupRNK - Branching Corner End Pole
	Place the pole where the line changes direction and where you want to run the branch line to the building(s). To achieve 	the proper rotation, you need to determine how many degrees the line should change direction in a given direction. After 	you have at least one post after the post at the bend, you need to rotate the corner post by half the determined value in 	the opposite direction (e.g., the line previously had a direction of 0 degrees, now it has a direction of 30 degrees, so 	the change is 30 degrees, and the post at the bend will have a rotation of 15 degrees, the formula for rotation is 	direction in front + direction behind / 2).

slupO - Retaining Post
	It is placed in a straight line where the line does not change direction, usually after long sections of the line. It can 	act as a through-and-crossing post.

slupON - Retaining and Corner Post
	It is placed where the line changes direction, usually after long sections of the line. To achieve the correct rotation, 	you need to determine how many degrees the line should change direction in a given direction. After you have at least one 	pole after the pole on the curve, you need to rotate the corner pole by half the designated value in the opposite direction 	(e.g., the line previously had a direction of 0 degrees, now it has a direction of 30 degrees, so the change is 30 degrees, 	and the pole on the curve will have a rotation of 15 degrees, the formula for rotation is direction in front + direction 	behind / 2). You also need to rotate the guy chains by half the previously determined direction change in the appropriate 	directions. The conductors on the pole must be selected manually by opening the group with the guy chain. The conductor can 	be rotated independently of the chain. The side of the pole with the support and the conductor hanging under the crossarm 	must be on the side to which the line turns. 

slupROK - branch-resistance-terminal pole
	It is placed in a straight line where the line does not change direction, usually along long sections of the line (it can 	act as a through-crossing pole), at the point from which we want to run a secondary line (for MV - to the transformer). If 	the pole has the suffix "s" (ROKs), an O (resistance)/ON (resistance-corner)/Or (resistance with a disconnector)/ONr 	(resistance-corner with a disconnector) pole must be located on the side of the secondary line, no more than 8m from this 	pole. The pole's support must be on the side of the secondary line conductors.

slupRONK - branch-resistance-corner-terminal pole
	We place it where the line changes direction, usually after long sections of the line, at the point from which we want to 	run a branch line (for MV lines, to a transformer). To achieve the appropriate rotation of this pole, we need to determine 	how many degrees the line should change direction in a given direction. After we have at least one pole positioned after 	the pole at the bend, we need to rotate the corner pole by half the designated value in the opposite direction (e.g., the 	line previously had a 0-degree direction, now it has a 30-degree direction, so the change is 30 degrees, and the pole at 	the bend will have a 15-degree rotation, the formula for rotation is direction in front + direction behind / 2). We also 	need to rotate the guy chains by half the previously determined change in direction in the appropriate directions. The 	conductors on the pole must be selected manually by opening the group with the guy chain. The conductor can be rotated 	independently of the chain. The side of the pole with the support and the conductor running under the crossarm must be on 	the side where the line turns.

slupOr - Retaining Pole with a Disconnector
	It is placed in a straight line where the line does not change direction, usually after long sections of line. It can act 	as a through-and-crossing pole. It must be located at least once on a side line (it does not have to be if a No. 0 pole is 	already on it).

slupONr - Retaining-Corner Pole with a Disconnector
	It is placed where the line changes direction, usually after long sections of line. To achieve the correct rotation, you 	need to determine how many degrees the line should change direction in a given direction. After you have at least one post 	after the post at the bend, you need to rotate the corner post by half the designated value in the opposite direction 	(e.g., the line previously had a direction of 0 degrees, now it has a direction of 30 degrees, so the change is 30 degrees, 	and the post at the bend will have a rotation of 15 degrees, the formula for rotation is direction in front + direction 	behind / 2). You also need to rotate the guy chains by half the previously determined direction change in the appropriate 	directions. The side of the post with the support must be on the side to which the line turns. It must be located at least 	once on the side line (it doesn't have to be if the 0r post is 	already on it).

slupK - end post
	This post is placed at the end of the line. Kp posts (the support must be on the side of the conductors) and Ko posts (the 	guy must be on the side opposite the conductors) can only be used on side lines.

slupKK - Terminal Pole
	Place it where the line changes direction by 90 degrees (e.g., at the end of a line with a direction of 0 degrees, where 	the next pole is 90 degrees).


TIPS:
It's best to replace components such as guy chains or insulators using the replace function.
To replace a lantern, remove the arm and lamp from the lantern group on the pole and paste the arm and lamp from the lantern group into this group from the "Accessories" group.
After replacing the MV insulators with composite ones, raise the conductors and terminals by 0.036 m. Simply add Y + 0.036 in the translation, and you're done.